- Pentair Mastertemp 400 Heater Manual
- Pentair Water Easy Touch Pool Heater User Manual Lx Manual
- Pentair Pool Products Manuals
- Pentair Service Manuals
May 27, 2016 Step by step instructions to turn on and adjust temp settings on a Pentair EasyTouch pool control system. How to make a pool heater under $100. Changing pump speed with Easy Touch. Jun 01, 2017 On page 66 of the 'easy touch 8 and 4 Pool and spa control system' user guide #521044, it walks you through the steps. We have a Pentair Water touch screen controller inside our house. The water pump went on this morning (which it should not have) and I want to turn it off. Or failure to properly maintain products as specified in the.
i
EasyTouch Load Center Installation Guide
Contents
IMPORTANT SAFETY INSTRUCTIONS ........................................................................ ii
General Installation Information ...................................................................................... iii
Technical Support ........................................................................................................... iv
EasyTouch 8 and 4 Pool and Spa Control System Kit Contents ..................................... 1
EasyTouch Accessory Equipment ................................................................................... 1
EasyTouch System Installation Steps Summary ............................................................. 2
Required Tools ................................................................................................................ 2
Plumbing Requirements ................................................................................................. 3
Equipment Location ........................................................................................................ 4
EasyTouch Load Center High Voltage Connections ....................................................... 6
EasyTouch Load Center Location ................................................................................... 6
Preparing the EasyTouch Load Center ........................................................................... 8
Mounting the EasyTouch Load Center ............................................................................ 9
Removing Electrical Conduit Knockouts ....................................................................... 10
Installing Conduit and Wire to the EasyTouch Load Center .......................................... 11
EasyTouch Motherboard Connections .......................................................................... 13
Accessing the EasyTouch Motherboard ........................................................................ 14
Installing Auxiliary Relays ............................................................................................. 15
Installing Valve Actuators .............................................................................................. 16
Installing and Connecting Temperature Sensors ........................................................... 17
Water Temperature Sensor ........................................................................................ 17
Ambient Air Temperature (Freeze Protection) Sensor ................................................ 17
Solar Temperature Sensor (Optional) ........................................................................ 17
Connecting the Heater Thermostat ............................................................................ 18
Connecting the IntelliChlor Cell .................................................................................... 19
Rewiring the IntelliChlor Transformer for 115 VAC ........................................................ 20
EasyTouch System Start-Up ......................................................................................... 21
Verifying IntelliChlor Power ........................................................................................... 22
EasyTouch System Wiring Diagram .............................................................................. 23
Glossary ........................................................................................................................ 24
6
EasyTouch Load Center Installation Guide
EasyTouch Load Center High Voltage Connections
The EasyTouch load center enclosure includes a 125/220 VAC 125 AMP circuit breaker base (sub-
panel), high-voltage power relays, transformer, and low voltage circuit breakers.
WARNING - BEFORE REMOVING THE HIGH VOLTAGE COVER PANEL FROM THE
ENCLOSURE switch the main power OFF into the home at the main circuit breaker box. Also,
switch OFF the main power to the EasyTouch load center before removing the high voltage cover
panel to access the low voltage raceway.
EasyTouch Load Center Location
Before installing the EasyTouch load center read the following guidelines:
•
AC power for the EasyTouch load center must be provided from the main circuit breaker
panel located at the house.
•
All electrical equipment, except for UL Listed spa-side remote switches, must be installed at
least five (5) feet from pool and/or spa, and comply with all national, state, and local codes
(UL Listed spa-side remote switches may be installed at near waterline).
•
Install the EasyTouch load center no less than five (5) feet from pool or spa near to the
pumps, heater, valves, and sensors. Mount the enclosure outside or inside a pool equipment
house or other enclosure.
•
Before choosing the final location for the EasyTouch load center, consider the length of the
wires and valve wires that have to be connected to the enclosure. Make sure to consider
cable lengths for the sensors to the EasyTouch load center location. The Air Temperature
Sensor cable is 3 feet long and the Water Temperature Sensor is 25 feet long.
•
Mount the EasyTouch load center on a flat vertical surface or wall so that the conduit
knockouts are located at the bottom of the enclosure. Upper and lower brackets are
provided to mount the enclosure to a vertical surface.
•
DO NOT mount the EasyTouch load center enclosure horizontally. Water can enter the
conduit knockouts and cause damage to the system and an electrical shock hazard.
Pentair Mastertemp 400 Heater Manual
•
Consider the EasyTouch load center location when routing the conduit carrying the AC
power to the EasyTouch load center, and the conduit that will be run to the high voltage
equipment.
•
Install the EasyTouch load center so that drainage is provided for all electrical components.
•
Motors should have built-in thermal protection.
•
Allow for unobstructed access to the front of the EasyTouch load center for the owner or
service personnel.
•
Pentair Water Easy Touch Pool Heater User Manual Lx Manual
The EasyTouch load center provides grounding screw terminals for grounding all equipment.
Pentair Pool Products Manuals
All equipment including the EasyTouch load center enclosure must be bonded to earth
ground.