View and Download Life Fitness Treadmill 97Ti operation manual online. Life Fitness Treadmill Operation Manual. Treadmill 97Ti Treadmill pdf manual download. Also for: 95t. This Operation Manual describes the functions of the following product: Life Fitness Treadmill Model: T3 Thank you for purchasing a Life Fitness treadmill. Before using this product please read this user manual in its entirety to ensure that you have the knowledge to safely and properly operate all of the features on your treadmill. We have 10 Life Fitness 95Ti manuals available for free PDF download: Service Manual, Operation Manual, Installation Instructions Manual, Specification, General Assembly. Life Fitness 97Ti Treadmill Specifications 54. Life Fitness 95Ti Operation Manual (44 pages). Life Fitness Manuals. Below we have uploaded the manuals and brochures of some of our most popular Life Fitness machines. If there is a manual for a certain piece of gym equipment that we have not uploaded here, please contact us at email protected and we will do our best to post it here. View and Download Life Fitness Treadmill 95Ti parts manual online. Life Fitness Treadmill General Assembly. Life Fitness 97Ti Service Manual 202 pages. Life fitness treadmill user manual (8 pages) Treadmill Life Fitness 10 90 Series Brochure & Specs. 90 series cardio (5 pages) Treadmill Life Fitness 95T Assembly Instructions Manual. Life Fitness Model 97Te, 95Te, 97Ti, 95Ti and 93T Arctic Silver Treadmills Theory of Operation The Treadmill is an electromechanical device that operates on A/C Voltage System and is controlled through the electronics in the Display Console. The key components that make up the Treadmill are the.

3.2 H

EART

R

ATE

M

ONITORING

T

HE

L

IFEPULSE

TM

S

YSTEM

To use the treadmill’s Lifepulse

TM

system to check the heart rate during a workout, grasp the stainless

steel sensors on the Ergo

TM

front handlebar. Two sensors are located on each of the handlebars.

Contact must be maintained with all four sensors to obtain a heart rate. The console displays a heart
rate within 20 to 30 seconds of contact with the sensors.

Do not attempt to grasp the sensors at speeds above 4.5 MPH, or 7.2 KPH. For these speeds, the
use of a heart rate chest strap is recommended.

T

HE

O

PTIONAL

H

EART

R

ATE

C

HEST

S

TRAP

The Life Fitness Treadmill is equipped with Polar® telemetry, a heart rate monitoring system in which
electrodes, pressed against the skin, transfer heart rate signals to the treadmill console. These electrodes
are attached to a chest strap that the user wears during the workout. The chest strap is optional. To order
it, call Life Fitness Customer Support Services at 1-800-351-3737.

See the diagram below for correct positioning of the strap. The electrodes (A), which are the two
grooved surfaces on the underside of the strap, must remain wet to transmit accurately the electrical
impulses of the heart back to the receiver. Moisten the electrodes. Then, secure the strap as high
under the chest muscles as possible. The strap should be snug, but comfortable enough to allow for
normal breathing.

The transmitter strap delivers an optimal heart rate reading when the electrodes are in direct contact
with bare skin. However, it functions properly through a thin layer of wet clothing.

If it becomes necessary to re-moisten the chest strap electrodes, grasp the center of the strap, pull it
away from the chest to expose the two electrodes, and re-moisten them.

During the setup of a heart rate zone training workout, the user will be required to enter a start-up
speed. If a heart rate chest strap is not detected, the maximum allowable speed is 4.5 mph. If a heart
rate chest strap is detected, the maximum speed is 12 mph (15 mph on the 97Ti).

A

Life Fitness 95ti Treadmill Manual

A

19

Assembly Instructions

Congratulations...

and welcome to the world of

The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set-up of this treadmill as quick and easy as possible.

Please take special note of the following important points prior to choosing a location and beginning assembly of the treadmill…

IMPORTANT SAFETY INSTRUCTIONS !

DO NOT position the rear of the treadmill within 6 feet ( 2 meters ) of the nearest obstruction. The sides of the treadmill should maintain a minimum clearance of 8 inches ( 20 cm ) from the nearest treadmill or other obstruction.

DO NOT locate the treadmill outdoors, near swimming pools, or in areas of high humidity.

DO verify the contents of the delivery carton against the accompanying parts listing prior to setting the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer Support Services at the number listed on the back page of this assembly instruction booklet.

Save the shipping cartons in case of return.

DO read the entire Operation Manual prior to attempting to operate this machine, as this is essential for proper use. The Manual explains how to properly use the treadmill and helps you to train your staff effectively.

NE placez PAS l’arrière du tapis roulant dans un rayon de 2 m (6 pi) de l’obstruction la plus proche. Les côtés de l’appareil ne doivent pas se trouver à moins de 20 cm (8 po) du tapis roulant voisin ou de toute autre obstruction.

NE placez PAS le tapis roulant à l’extérieur, près d’une piscine ou dans des endroits très humides.

VÉRIFIEZ si l’emballage contient toutes les pièces de la liste jointe avant de le mettre de côté. Si des pièces sont absentes, contactez l’assistance clientèle de Life Fitness au numéro indiqué au dos de cette brochure d’instruction de montage..

VÉRIFIEZ si l’emballage contient toutes les pièces de la liste jointe avant de le mettre de côté. Si des pièces sont absentes, contactez l’assistance clientèle de Life Fitness au numéro indiqué au dos de cette brochure d’instruction de montage.

TOOLS REQUIRED FOR ASSEMBLY...

Phillips screwdriver, Torx wrench, 3/4” combination wrench, flat blade screwdriver (or 5/16” nut driver)

PARTS DESCRIPTION

IMPORTANT!

DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS

NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.

IMPORTANT!

NE JETEZ PAS LE KIT D’EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT TOUS LES

ÉLÉMENTS NÉCESSAIRES POUR L’INSTALLATION.

1.Remove the four SCREWS (A) securing the FRONT GRILL (B) to the FRAME (C). Remove the FRONT GRILL and set it aside.

2.Remove the four SCREWS (D) securing the MOTOR COVER (E). Lift and remove the MOTOR COVER and set it aside.

3.Locate the LEFT UPRIGHT (#1). Lay the LEFT UPRIGHT across the belt and deck with the notched end near the LEFT UPRIGHT MOUNTING BRACKET (F).

4.Unwrap the MAIN WIRE HARNESS (G) leading from the LEFT UPRIGHT MOUNTING BRACKET (F). Feed the MAIN WIRE HARNESS through the LEFT UPRIGHT (#1). Carefully tilt the LEFT UPRIGHT upwards and position the notched end of the LEFT UPRIGHT over the LEFT UPRIGHT MOUNTING BRACKET. With the LEFT TOP MOUNTING PLATE (H) directed forward, slide the LEFT UPRIGHT down over the LEFT UPRIGHT MOUNTING BRACKET and pre-installed BOLT and WASHER until it rests on the FRAME (C). Secure the LEFT UPRIGHT to the LEFT UPRIGHT MOUNTING BRACKET using two BOLTS (#20) and WASHERS (#24). One BOLT and WASHER on the inside of the LEFT UPRIGHT and one BOLT and WASHER on the front side of the LEFT UPRIGHT. Leave the BOLTS loose at this time.

NOTE: BE CAREFUL NOT TO DAMAGE THE MAIN WIRE HARNESS (G) WHEN ROUTING IT THROUGH THE LEFT UPRIGHT (#1) OR WHEN SLIDING THE LEFT UPRIGHT OVER THE LEFT UPRIGHT MOUNTING BRACKET (F).

NOTE: BE SURE THE PRE-INSTALLED WASHER IS ON THE OUTSIDE OF THE LEFT UPRIGHT (#1) WHEN SLIDING IT DOWN TO REST ON THE FRAME (C).

5.Locate the RIGHT UPRIGHT (#2). With the RIGHT TOP MOUNTING PLATE (J) directed forward, slide the RIGHT UPRIGHT down over the RIGHT UPRIGHT MOUNTING BRACKET (K) and pre-installed BOLT and WASHER until it rests on the FRAME (C). Secure the RIGHT UPRIGHT to the RIGHT UPRIGHT MOUNTING BRACKET using two BOLTS (#20) and WASHERS (#24). One BOLT and WASHER on the inside of the RIGHT UPRIGHT and one BOLT and WASHER on the front side of the RIGHT UPRIGHT. Leave the BOLTS loose at this time.

NOTE: BE SURE THE PRE-INSTALLED WASHER IS ON THE OUTSIDE OF THE RIGHT UPRIGHT (#2) WHEN SLIDING IT DOWN TO REST ON THE FRAME (C).

6.(Model 93T Only) Locate both HANDLEBARS (#3). Slide one HANDLEBAR GROMMET (#27) over each HANDLEBAR. The groove of the HANDLEBAR GROMMET should face outward.

7.With the bend of one HANDLEBAR (#3) directed to the outside of the treadmill, insert the HANDLEBAR into the RIGHT UPRIGHT HANDLEBAR BRACKET (L) as shown. Be sure the HANDLEBAR MOUNTING HOLES are aligned. Repeat for the left side HANDLEBAR.

8.Locate the ERGO™ FRONT CROSSBAR (#4) and position the ERGO FRONT CROSSBAR with the plastic SMART STOP COVER (M) facing upward and forward as shown. Locate and slide the left and right INSIDE HANDLEBAR SHROUDS (#5 & #6) over the corresponding ends of the ERGO FRONT CROSSBAR as shown. Slide the left and right INSIDE HANDLEBAR SHROUDS towards the center of the ERGO FRONT CROSSBAR as shown.

NOTE: BE CAREFUL NOT TO DAMAGE THE ANY WIRE HARNESSES THAT MAY BE LEADING FROM THE ENDS OF THE ERGO FRONT CROSSBAR (#4).

9.Install one FRONT CROSSBAR GROMMET (#26), rounded end first, over either end of the ERGO FRONT CROSSBAR (#4). Position the grommets just over the end brackets to meet the overmolding.

NOTE: BE CAREFUL NOT TO DAMAGE THE ANY WIRE HARNESSES THAT MAY BE LEADING FROM THE ENDS OF THE ERGO FRONT CROSSBAR (#4).

G

2

20 24

20 24

24

M 6 26

5

19 4

N 2

3 17

10.Position the right end of the ERGO FRONT CROSSBAR (#4) near the large access hole on the inside of the RIGHT UPRIGHT HANDLEBAR BRACKET (L).

Align the ERGO FRONT CROSSBAR MOUNTING HOLES with those in the RIGHT UPRIGHT HANDLEBAR BRACKET and secure using two BOLTS (#19), from the inside of the treadmill, and NUTS (#22). Tighten the BOLTS securely. Insert one SCREW (#16) from under the RIGHT UPRIGHT HANDLEBAR BRACKET. Tighten the SCREW securely.

11.Position the left end of the ERGO FRONT CROSSBAR (#4) near the large access hole on the inside of the LEFT UPRIGHT HANDLEBAR BRACKET (N).

(Models 97Ti and 95Ti Only) Feed the SMART STOP CABLE (O) and HEART RATE CABLE (P) into the access hole downward out the bottom of the LEFT UPRIGHT HANDLEBAR BRACKET.

Align the crossbar mounting holes with those in the LEFT UPRIGHT HANDLEBAR BRACKET and secure using two BOLTS (#19), from the inside of the treadmill, and NUTS (#22). Tighten the BOLTS securely. Insert one SCREW (#16) from under the LEFT UPRIGHT HANDLEBAR BRACKET. Tighten the SCREW securely.

NOTE: BE CAREFUL NOT TO PINCH THE SMART STOP CABLE (O) AND HEART RATE CABLE (P) (IF EQUIPPED) WHEN ASSEMBLING THE ERGO FRONT CROSSBAR (#4) TO THE LEFT UPRIGHT HANDLEBAR BRACKET.

(Models 97Ti and 95Ti Only) Feed the SMART STOP CABLE (O) and HEART RATE CABLE (P) upward through the top of the LEFT UPRIGHT (#1).

12.Slide the LEFT INSIDE HANDLEBAR SHROUD (#5) near the LEFT UPRIGHT HANDLEBAR BRACKET (N).

(Model 93T Only) Position the HANDLEBAR GROMMET (#27) at the end of the LEFT INSIDE HANDLEBAR SHROUD. Install the HANDLEBAR GROMMET onto the inside edge of the LEFT INSIDE HANDLEBAR SHROUD as shown.

Locate and position the LEFT OUTSIDE HANDLEBAR SHROUD (#7) to match the LEFT INSIDE HANDLEBAR SHROUD.

(Model 93T Only) Install the remaining portion of the HANDLEBAR GROMMET onto the LEFT OUTSIDE HANDLEBAR SHROUD as it is positioned to match the LEFT INSIDE HANDLEBAR SHROUD.

Secure the SHROUDS together using three SCREWS (#15). Tighten the SCREWS securely. Do not overtighten the SCREWS. Repeat the procedure for the RIGHT INSIDE and OUTSIDE HANDLEBAR SHROUDS (#6 and #8).

13.Locate the DISPLAY CONSOLE (#9). Remove the eight SCREWS (Q) from the back of the DISPLAY CONSOLE and separate the front of the DISPLAY CONSOLE from the rear. Position the REAR CONSOLE (R) over the LEFT and RIGHT TOP MOUNTING PLATES (H & J) as shown. From the bottom of the LEFT and RIGHT TOP MOUNTING PLATES, secure the REAR CONSOLE using four screws (#17). Tighten the SCREWS securely. Do not overtighten the SCREWS.

20. Locate one SCREW GROMMET (#18). Insert the SCREW GROMMET into the square hole located above the top inside mounting bolt of the RIGHT UPRIGHT (#2). Repeat for the remaining SCREW GROMMET and LEFT UPRIGHT (#1)

21.Locate one LOWER UPRIGHT COVER (#10). Position the LOWER UPRIGHT COVER at the bottom notch of the RIGHT UPRIGHT (#2) making

and remaining UPRIGHT COVER.

22. Locate the UPRIGHT PLUGS (#25). Insert one UPRIGHT PLUG into each of the two access holes located on the lower outside of the LEFT and RIGHT UPRIGHTS (#1 & #2).

23. Locate and press the HANDLEBAR CAPS (#13) over the ends of the HANDLEBARS (#3). Be sure the HANDLEBAR CAPS are fully seated.

24. Using two SCREWS (#16) each, attach the two REAR FRAME END CAPS (#14) to the FRAME (C) as shown. Tighten the SCREWS securely. Do not overtighten the SCREWS.

13

14

PRE-OPERATION CHECKLIST

Ensure that all fasteners are tight.

Make sure the STRIDING BELT is properly tensioned and aligned according to the Operation Manual.

Check the operation of the STOP switch and tether switch assembly.

(See Operation Manual.)

Confirm the display console is set to English or Metric units. (See Optional Settings ENG/MET in Operation Manual.)

Refer to the Operation Manual for real time clock setting.

Read the entire Operation Manual before using the treadmill.

LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE

Vérifiez si tous les dispositifs de fixation sont serrés.

Assurez-vous que le TAPIS est bien tendu et aligné, conformément aux instructions du manuel d’utilisation.

Vérifiez le fonctionnement de l'interrupteur d'ARRÊT et reliez-le

(cf. Manuel de l'utilisateur).

Vérifiez si la console d’affichage est sur le système métrique ou anglais.

(Référez-vous aux réglages facultatifs relatifs aux systèmes de mesure dans le Manuel de l’utilisateur.)

Consultez le Manuel de l’utilisateur pour le réglage de l’horloge en temps réel.

Life Fitness 97ti Treadmill User Manual Pdf

Lisez le Manuel de l’utilisateur dans son intégralité avant d’utiliser le tapis roulant.

Before attempting to operate your Treadmill, it is imperative that you familiarize yourself with the contents of the Operation Manual. If your Life Fitness treadmill does not respond as described in the OPERATION MANUAL contact the nearest Life Fitness Service Center as listed in the OPERATION MANUAL.

Life Fitness Customer Support Services

(800) 351-3737 or (847) 451-0036

Prior to your call, please be sure you have located and noted the

MODEL NUMBER & SERIAL NUMBER.

The Model & Serial number information of your Life Fitness Treadmill is contained in a label located on the front of the unit.

©2004 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness, Lifepulse, FlexDeck and Smart Stop are trademarks of Brunswick Corporation.

Polar is a registered trademark of Polar Electro, Inc. MO51-00K58-A181 09.04